10 x 100 g Additive to solid fuels SADPAL II - soot combustion catalyst
Catalyst for soot combustion
Additive to solid fuels
It is typically used for complete afterburning of soot in every location in the boiler (furnace, combustion chamber, chimney canals).
SADPAL II has over 30 times bigger adhering surface. It presents much higher effectiveness due to the fact, that it evaporates much quicker in the flame of a buring wood. Consequently, Sadpal II reacts a lot faster with the fumes coming from the burned wood.
IT IS NEITHER EXPLOSIVE NOR FLAMMABLE
REDUCTIONS IN CHARGES FOR ATMOSPHERE POLLUTING
Providing that “SADPAL” product is used regularly, the following reductions in payments are possible:
- for solid grates up to 55%;
- for mechanical grates up to 25%;
APPLICATION OF “SADPAL” ELIMINATES
1. polluting of atmosphere with soot (black smoke);
2. higher fractions of aromatic polycyclic aromatic
hydrocarbons /PAH/,including 3,4-benzopirane;
3. emission of carbon monoxide into atmosphere;
4. requirement to perform mechanical removal of soot sediments from
5. down-time related to mechanical removal of soot sediments from
6. soot combustion in the chimney canal.
IT ALSO CAUSES REDUCTION IN:
1. emission in sulphur dioxide into the atmosphere by approximately 12 –
20% due to coal savings;
2. coal consumption, ranging from 12 to 20% depending on its caloric
3. the content of SO2 and NOx in combustion fumes, ranging from 10
4. corrosion speed of steel construction elements of grate furnaces in
boilers and combustion gases disposal installations;
5. increases the efficiency of cyclones, multicyclones and electrofilters.
UTILITARIAN PROPERTIES AND APPLICATION RANGE OF “SADPAL”
“SADPAL” is a green powder – a mixture of inorganic salts, which are subject to decomposition into substances with catalytic properties under temperatures in excess of 65şC.
This product is used to combust soot and organic substances to their final products – carbon dioxide and water.
Application of “SADPAL” does not pose threat to grate furnaces and combustion gases disposal installations; quite on the contrary – it extends their life cycle (expert opinion of the Institute of Material Science, School of Mining and Metallurgy in Cracow from the 20th of February 1991).
“SADPAL” improves life cycles for cyclones, multicyclones and electrofilters.
It is not a flammable or toxic product (evaluation issued by the National Institute of Hygiene in Warsaw, number 24/B-23/91), is not explosive and does not pose threat related to its improper application or over-dosage. Since 1991 it has been successfully applied in hundreds of plants and thousands of individual customers.
SADPAL” eliminates soot and fly-ash through their combustion.
Uncombusted hydrocarbons, including benzopirane, are combusted together with soot deposits. Carbon monoxide is combusted to carbon dioxide.
Reduction in the level of SO2 by approximately 10-20% and NOx by approximately 5 -10% in the combustion gases is the direct result of their being bound by the chemical components of “SADPAL”.
“SADPAL” demonstrates activity in the following groups:
- cleaning of the boiler surfaces;
- enhancement of the combustion processes – decrease in the amount of solid molecules included in the combustion gases and decrease inthe carbon dioxide concentration;
- reduction in the SO2 and NOx concentrations;
- reduction in the high and low temperature corrosion;
- reduction in the total dust content;
Regular application of “SADPAL” with the application ratio of 1 – 2 kilograms per a tone of coal eliminates any deposits in the furnace and heating pipes, maintaining them in working order during the heating season.
Thanks to that, the down-time designated for furnace cleaning is short and only involves the removal of ashes collected in the back part of the furnace.
As a direct result of “SADPAL” application, the ash deposits change their structure, become loose and fall off the walls, because the soot – which was keeping them together – was burned out. Newly sedimented ash deposits are burned out immediately – the walls of the furnace remain clean all the time.
“SADPAL” does not cause additional mineral sedimentation on heating
elements (heating screens) – it does not contain any dolomite in its structure.
Due to its numerous and above mentioned advantages, it is widely applied during exploitation of furnaces heated with coal, fine coal, wood, peat, brown coal, both in medium and large heat generation plants. It significantly improves the boiler efficiency, at the same time keeping its walls clean. Every millimetre of sediment (slag, soot sediment) of the boiler’s wall increases fuel consumption by 10%.
Drop a sachet of SADPAL II onto the embers of a fireplace insert or a small boiler. Check after 30 - 40 minutes and, if necessary, drop in another sachet. The amount of SADPAL used depends on the size of a boiler or a fireplace insert. The product is packed in 10 x 100 g sachets. The estimate dosage is 25 g of SADPAL for every 4-6 kg of ember. Nevertheless, the dose ought to be estimated experimentally, there is no possibility of overdosing and the deficiency can be spoted by looking at the sides of the fireplace inset or the boiler. The addition of SADPAL II gives a visual sensation in the form of yellow-and-blue flame.
COST EFFECTIVENESS OF “SADPAL II” APPLICATION
- elimination of soot due to its complete combustion;
- elimination of benzopirane;
- reduction in carbon monoxide emission, reduction in total emission of combustion gases by approximately 10- 20% due to savings on solid fuel consumption;
- reduction in emissions of SO2 by approximately 10-20% and NOx by approximately 5-10%;
- reduction in the total amount of slag and ash production due to savings on solid fuel consumption;
- reduction in emission of ashes.
- payment reductions ranging from 25 to 55% due to elimination of soot,
benzopirane, reduction in CO, SO2 and NOx emissions, reduction in total dust content;
- coal consumption savings ranging from 10 to 20%;
- maintaining boilers and furnaces in working order during the heating season due to elimination of slag sediments;
- elimination of mechanical cleaning of boilers and furnaces;
- reduction in down-time related to mechanical removal of soot and slag sediments in the boilers and furnaces;
- extension in life expectancies for steel construction elements of grate furnaces in boilers and combustion gases disposal installations;
- improvement in the efficiency of dust removing mechanisms;